Steel Shot S110-S780: Shot Peening and Blast Cleaning Media

Item: Details
Product Name: Steel Shot
Grades: S110 / S170 / S230 / S280 / S330 / S390 / S460 / S550 / S660 / S780
Hardness: HRC 40-50 (standard) and HRC 55-65 (high hardness)
Chemical: C 0.8-1.2%, Si 0.4-1.2%, Mn 0.6-1.2%
Bulk Density: 1.3-1.5 g/cm3
Core Advantages: Round and uniform, stable peening intensity, low breakage, recyclable
Typical Use: Shot peening, blast cleaning, casting and forging cleaning, surface finishing
Packing: 25kg bag / 1000kg jumbo bag / 2000kg jumbo bag

Category:Steel Shot

Product Details

Steel shot is round media: atomised steel, heat-treated, screened to a tight size band and checked for roundness. Roundness is the whole point — a round shot peens and finishes, an angular one cuts. If your process is shot peening to a controlled Almen intensity, the shot has to be consistently round and consistently hard.

The S Size Scale

S110 ≈ 0.3 mm Fine peening, small precision parts
S170 / S230 ≈ 0.4–0.6 mm General peening, automotive components
S280 / S330 ≈ 0.7–0.9 mm Heavier peening, castings and forgings
S390–S550 ≈ 1.0–1.7 mm Blast cleaning, large castings
S660 / S780 ≈ 2.0–2.5 mm Heavy cleaning, ingot and slab

Typical Specification

Carbon 0.8–1.2%
Silicon 0.4–1.2%
Manganese 0.6–1.2%
Hardness HRC 40–50 standard / 55–65 high
Bulk density 1.3–1.5 g/cm³
Shape Spherical, minimum 85% round

Steel shot round metallic spheres used for shot peening

Peening or Cleaning?

The two uses want different specs. Peening wants small, hard, very round shot with low breakage and a stable size distribution, because intensity and coverage depend on it. Cleaning wants larger shot, more tolerance on roundness, and hardness chosen to match the consumption budget. Running one grade for both usually costs money somewhere.

Where It Is Used

  • Shot peening — aerospace, automotive springs, gears, turbine blades, landing gear
  • Blast cleaning — castings, forgings, heat-treated parts, plate and profiles
  • Casting cleaning — removal of sand and scale in foundry machines
  • Surface finishing — satin and uniform cosmetic finishes
  • Stone cutting — gang saw shot for granite blocks

Keeping Consumption Down

Most shot loss comes from three places: an over-aggressive separator pulling good shot into the dust, worn wheel blades throwing the pattern off target, and mixed sizes accumulating fines in the machine. Check the separator setting monthly, replace blades on schedule and top up with a single size rather than blending leftovers.

Packing

  • 25 kg bags on pallets
  • 1 tonne and 2 tonne jumbo bags
  • Steel drums where moisture control matters

Abrasive jumbo bags being loaded into a shipping container

Common Questions

What hardness should I buy?
Standard HRC 40–50 for long life in cleaning machines, high hardness HRC 55–65 where faster cleaning justifies higher breakage.

Do you supply peening-grade shot with certificates?
Yes — specify the grade and we supply with a batch report covering size and hardness.

Can I mix S230 and S330?
It works for cleaning, but do not blend sizes for controlled peening.

Get a Quote

Tell us whether the job is peening or cleaning, the machine type and the shot size you run now, and we will confirm the grade and price within 24 hours. Contact us here or see the steel shot range.

Inquiry