





Waterjet Garnet Sand 80 Mesh: Cut Speed, Consumption and Price
Item: Details
Product Name: Waterjet Garnet Sand 80 Mesh
Grade: 80 mesh (about 0.18 mm), 80A / 80HP on request
Raw Material: Natural Almandine Garnet
Mohs Hardness: 7.5-8.0
Specific Gravity: 3.8-4.1 g/cm3
Chloride Content: less than 25 ppm
Core Advantages: Sharp angular grains, stable feed rate, clean cut edge, low dust, silica-free
Typical Use: Waterjet cutting of steel, stainless, aluminium, glass, stone and composites
Packing: 25kg bag / 1000kg jumbo bag / 2000kg jumbo bag
Port: Tianjin or Qingdao
Category:Garnet sand
Product Details
If your waterjet runs one abrasive most of the time, it is almost certainly 80 mesh garnet. Coarse enough to cut, fine enough to leave a clean edge, and cheap enough to run all day — it sits in the middle of the range and covers about three quarters of the jobs a job shop sees. Below is what actually matters when you buy it by the tonne.

Why 80 Mesh Wins as the Default
Waterjet nozzles run at 30,000–60,000 psi and mix abrasive into the stream at a controlled rate. The grit has to be small enough to pass the mixing tube without clogging, hard enough to survive the trip, and sharp enough to cut. At 80 mesh — roughly 0.18 mm — garnet hits all three. Try 60 mesh and the cut speeds up on thick plate but the edge gets raggier and the mixing tube wears faster; try 120 mesh and the edge is beautiful but the cut slows and consumption per metre of cut climbs.
How Much a Tonne Actually Cuts
Most machines draw between 0.2 and 0.45 kg of abrasive per minute, depending on orifice and abrasive flow setting. At 0.3 kg/min, a tonne lasts about 55 hours of cutting time. Measured against the job, a common figure is 0.15–0.4 kg per metre of cut in 10 mm mild steel; thick plate and slow feed push that up, thin sheet and fast feed pull it down.
The number that matters for quoting is cost per metre, not cost per tonne: price per tonne divided by 1,000, multiplied by consumption per metre.
What Moves the Price per Tonne
- Grade consistency — tightly screened 80 mesh with low fines costs more than a loose cut, and it feeds better
- Chloride and moisture — dried, low-chloride material protects pumps, mixing tubes and precision parts
- Packing — 25 kg bags on pallets cost more in labour than 1 tonne or 2 tonne jumbo bags
- Port and terms — FOB Tianjin or Qingdao, or CIF to your discharge port; freight dominates on long routes
- Volume — a full 20′ container of 25–27 tonnes is priced very differently from a one-tonne trial
Typical Specification
| Grain size | 80 mesh, about 0.18 mm |
| Mohs hardness | 7.5–8.0 |
| Specific gravity | 3.8–4.1 g/cm³ |
| Bulk density | 1.9–2.1 g/cm³ |
| Chloride | < 25 ppm |
| Free crystalline silica | None |
| Grain shape | Angular, sub-angular |

80 Mesh vs 60 and 120 Mesh
| Grade | Cut speed | Edge quality | Best for |
| 60 mesh | Fastest | Rougher, wider kerf | Thick plate, rough cut, stone |
| 80 mesh | Fast | Good, near-machined | General steel, stainless, aluminium |
| 120 mesh | Slower | Best, fine finish | Thin sheet, glass, composites, finishing passes |
Many shops keep 80 mesh as the workhorse and a pallet of 120 mesh for finishing jobs. That combination covers more work than trying to run one grade for everything.
Buying Checklist
- Ask for the sieve analysis, not just the mesh name — a “80 mesh” that is half fines will cost you cutting speed
- Confirm chloride and moisture limits if you cut aerospace, medical or stainless parts
- Decide packing by handling method: 25 kg bags for manual, 1 tonne or 2 tonne jumbo bags for crane and forklift
- Trial one tonne before committing to a container; check feed stability and edge quality on your own machine

Common Questions
Is 80 mesh the same as 80A?
Both are 80 mesh; the letter refers to grade quality. Ask for the sieve and chloride data rather than relying on the label.
How many tonnes do I need per month?
Multiply hourly consumption by cutting hours. A single machine running one shift typically uses 1.5–3 tonnes a month.
Can I mix 80 and 120 mesh?
Do not blend them — you lose the benefit of both. Keep them in separate hoppers.
Get a Quote
Send your machine model, mixing tube size and monthly consumption, and we will quote 80 mesh garnet FOB Tianjin or Qingdao within 24 hours, with sieve analysis attached. Contact us here, read the full waterjet mesh and cost guide, or see the whole garnet sand range.




